November 2, 2026
The IP67 rating is often seen as a ‘solve-all’ solution for enclosure sealing that is dust-tight and waterproof but the reality is far more nuanced. IP67 does not follow IP66 or precede IP68 in a series of linear ratings. Instead, the IEC-60529 IP67 standard adopts a two-digit designator where the first digit applies to the device’s protection against fine solids, such as dust particles and sand on a scale of 0-6 where 0 means there is no protection and 6 means there is full protection. The second digit follows a similar 0-9 scale for liquids where 9 indicates full protection against liquid ingress.
In a perfect world of totally-protected devices, an IP69 rating would ensure no fine particles and no liquid could penetrate the device but the cost and complexity of building casings and housings to the level 9 water ingress protection standard makes it cost-prohibitive for all devices. For many IP69 would be unnecessary and most use cases only need dust and waterproof enclosure designs to provide protection at much lower levels. A sweet-spot in the market has emerged with the IP67 designation, which provides full protection against solid particles and protects against liquids for at least 30 minutes when submerged in 1m of water.
The IP67 design guide specification covers the largest share of the market, protecting devices such as an IP67 GPS tracker or IP67 handheld computer against routine issues such as rain, splashing, momentary submerging in a puddle and airborne particulates. It finds a neat balance between cost, complexity and performance but, even so, there are significant considerations to address. A key ingredient in an IP67 rating is the selection of housing and sealing materials according to the device’s operating environment, temperature range and exposure to chemicals.
Enclosure sealing
Materials such as silicone rubber are widely used for consumer electronics and general enclosure sealing. This material is utilized because of its temperature tolerance, its ability to recover from compression and its general flexibility. Ethylene propylene diene monomer (EPDM) is typically adopted for more rugged, outdoor and industrial applications. This material offers greater resistance to UV light, harsh weather, aging and ozone effects. Polyurethane is also used extensively for heavy-duty industrial enclosures with liquid polyurethane foam often dispensed directly into the housing groove to create a seamless seal.
Other materials such as Viton are used in chemical and industrial situations where degradation from oils, fuels and surfactants that would damage standard silicone are used. In addition, engineering plastics such as acetal, polycarbonate and ABS or PC blends can be chosen for a housing because of their ability to provide high levels of structural rigidity with low moisture absorption. In high-corrosion marine environments, 316L stainless steel or anodized aluminum are used to ensure durability.
Design decisions
Rugged handheld computers, IP67 sensors, waterproof wearables and IP67 smart meters all require different approaches to mechanical design to deliver optimized protective performance. IP67 outdoor gateway enclosure design, for example, can be addressed by careful selection of controlled gasket compression criteria. Enclosures are engineered with dedicated rectangular or dovetailed grooves that retain the gasket in place during assembly to ensure a tight seal. Mechanical stops can be designed-in next to screw heads to prevent over-compression of the gasket material, which prevents cracking or deformation of rubber. An optimum level for gasket compression might be 20-40% and this can be specified and supported in the design of the device’s casing.
Consideration should also be given to the flatness and spacing of fasteners across the seal. These must be located close enough to enable a strong seal and prevent micro-gaps while also preventing the enclosure’s panels from bowing between the screws.
Where screws close the housing, the gasket does the sealing. Where screws can be eliminated, ultrasonic welding or adhesive bonding gives a more permanent joint. Welding fuses the mating plastic surfaces under high-frequency vibration into a molecular-level bond, requiring no gasket that can degrade with age and no need to apply compression. Bonding with a dispensed bead of silicone or polyurethane along the flange suits enclosures that will never be reopened, or that combine dissimilar materials, because a bonded joint is hard to take apart. Both welding and bonding are process-driven and the weld energy, joint geometry and bead placement must be verified during IP testing.
Depending on the use case, designs also need to accommodate entry and egress of cables from the housing and enable venting to external air sources in order to control temperature within the device. Conical and pass-through sealing for cables can be a source of water and dust ingress so sealing grommets that tightly grip the cable at two distinct points are specified to create dual-layered water barriers.
Vent the pressure
Temperature changes, which are particularly important for outdoor devices, force the internal air within the enclosure to expand or contract so venting is needed. An obvious problem with that is that a basic vent can allow ingress of dust or water so devices can be designed to use expanded polytetrafluoroethylene (ePFTE) membranes. Vents with these, allow air molecules pass freely while blocking liquid droplets from penetrating the enclosure.
When it comes to custom IoT development, the intricacies of achieving an IP67 rating can appear challenging and well outside the experience of in-house teams. It can therefore help to work with an IoT original device manufacturer (ODM) that is familiar with the IP67 test procedure to ensure optimized IP67 rating is achieved. An IoT ODM can take away the complexity and use its experience to ensure custom IoT devices bring the best blend of protection for your use case, with IP67 test capability to ensure the product meets the designation’sw requirements.
Whether you’re assessing if your product rating should be IP67 vs IP68 or looking to create an IP67 enclosure that can withstand extremes of temperature, a specialized IoT ODM, like Ikotek, has the experience and global engineering expertise to help you design devices that offer the ideal blend of performance, protection and price.
To learn more about Ikotek’s IP-rating expertise and how we can help you achieve IP67 rating without friction, contact us.